-5%
PWR-C45-6000ACV
Model: PWR-C45-6000ACV Cisco Catalyst 4500 PoE Enabled Power Supply
Details: Cisco Catalyst 4500 Power Supply PWR-C45-6000ACV Catalyst 4500 6000W AC dual input Power Supply (Data + PoE)
Condition: New Factory Sealed
Warranty: 3 Years Warranty.
Description
PWR-C45-6000ACV Overview
Quick Specs Figure 1 shows the appearance of PWR-C45-6000ACV.
Table 1 shows the Quick Specs.
| AC-input type | Autoranging inputs with power factor correctionNote Power factor correction is a standard feature on all Catalyst 4500 E-series AC-input power supplies. PFC reduces the reactive component in the source AC current allowing higher power factors (typically 99 percent or better) and lower harmonic current components. |
| AC-input voltage | Low-line (120 VAC nominal)—85 VAC (min) to 132 VAC (max)High-line (230 VAC nominal)—170 VAC (min) to 264 VAC (max) |
| AC-input current | 12 A (max) @ 120 VAC (for each input)16 A (max) @ 230 VAC (for each input) |
| AC-input frequency | 50/60 Hz (nominal) (±3% for full range) |
| Power supply output | Total output depends on the number of inputs connected and the source AC voltage. If two inputs are used, they should both be of the same AC voltage.1050 W operation (with one 120 VAC nominal input)– 70.8 A @ 12 VDC (data only)– 12.5 A @ 3.3 VDC (data only)– 18.4 A @ –50 VDC (PoE if used)2100 W operation (with two 120 VAC nominal inputs)– 141.6 A @ 12 VDC (data only)– 12.5 A @ 3.3 VDC (data only)– 37.0 A @ –50 VDC (PoE if used)3000 W operation (with one 230 VAC nominal input)– 183.3 A @ 12 VDC (data only)– 12.5 A @ 3.3 VDC (data only)– 48 A @ –50 VDC (PoE if used)6000 W operation (with two 230 VAC nominal inputs)– 183.3 A @ 12 VDC (data only)– 12.5 A @ 3.3 VDC (data only)– 96 A @ –50 VDC (PoE if used) |
| Power supply output capacity | 6000 W maximum |
| Output holdup time | 20 ms minimum |
| kVA rating5 | 6.8 kVA (power factor = 0.99) |
| Heat dissipation | 2,720 BTUs/hr (approx.) |
| Minimum software requirement | Cisco IOS Release 12.2(52)SG |
| Power over Ethernet | Supported, up to 4800 W |
| INPUT OK | Green—Source AC voltage is OK. (Input voltage is 85 VAC or greater.)Off—Source AC voltage falls below 70 VAC, is not present, or the power supply is turned off. |
| FAN OK | Green—Power supply fan is operating properly.Off—Power supply fan failure is detected. |
| OUTPUT FAIL | Red—Problem with one or more of the DC-output voltages of the power supply is detected.Off—DC-output voltage with acceptable margins.Note For proper operation of the OUTPUT FAIL LED, systems with single power supplies must be configured with a minimum of one fan tray assembly and one supervisor engine. Systems with dual power supplies must have a minimum configuration of one fan tray assembly, one supervisor engine, and one additional module. Failure to meet these minimum configuration requirements can cause a false power supply output fail signal. |
Get more information
Do you have any question about the PWR-C45-6000ACV?
Contact us now via Live Chat or sales@metafinitivetech.com
